CTFR 17/601,117 CTFR 92548 DETAILED ACTION Notice of Pre-AIA or AIA Status 07-03-aia AIA 15-10-aia The present application, filed on or after March 16, 2013, is being examined under the first inventor to file provisions of the AIA. Response to Arguments 07-37 AIA Applicant's arguments filed 05/14/2026 have been fully considered but they are not persuasive. Applicant argues that ¶ [0065] of the publication discloses the support for “wherein the disk covers an entirety of the second side of the stator.” Examiner disagrees. The paragraph discloses “the cooling body 10 corresponds approximately to an end-side are of the stator on the second side,” and approximate is defined as “close in value or amount but not precise,” which is not the same as “the disk covers an entirety of the second side of the stator.” Thus, the argument is not persuasive. Applicant argues that “the inner hole 13 of the cooling body 10 extends over the second side of the stator and approximates a rotor shaft protruding through the inner hole 13.” Examiner disagrees. The specification does not disclose a rotor shaft, nor does it disclose that the inner hole 13 approximates an outer radius of a rotor shaft. Thus, the argument is not persuasive . Claim Rejections - 35 USC § 112 07-30-01 AIA The following is a quotation of the first paragraph of 35 U.S.C. 112(a): (a) IN GENERAL.—The specification shall contain a written description of the invention, and of the manner and process of making and using it, in such full, clear, concise, and exact terms as to enable any person skilled in the art to which it pertains, or with which it is most nearly connected, to make and use the same, and shall set forth the best mode contemplated by the inventor or joint inventor of carrying out the invention. The following is a quotation of the first paragraph of pre-AIA 35 U.S.C. 112: The specification shall contain a written description of the invention, and of the manner and process of making and using it, in such full, clear, concise, and exact terms as to enable any person skilled in the art to which it pertains, or with which it is most nearly connected, to make and use the same, and shall set forth the best mode contemplated by the inventor of carrying out his invention. 07-31-01 Claims 1-17 are rejected under 35 U.S.C. 112(a) or 35 U.S.C. 112 (pre-AIA), first paragraph, as failing to comply with the written description requirement. The claim(s) contains subject matter which was not described in the specification in such a way as to reasonably convey to one skilled in the relevant art that the inventor or a joint inventor, or for applications subject to pre-AIA 35 U.S.C. 112, the inventor(s), at the time the application was filed, had possession of the claimed invention. Claim 1 recites “wherein the disk covers an entirety of the second side of the stator and the inner radius approximates an outer radius of a rotor shaft” which has not been disclosed in the original specification as filed. Claims 2-17 are rejected for depending upon claim 1. Drawings 06-36 AIA The drawings are objected to under 37 CFR 1.83(a). The drawings must show every feature of the invention specified in the claims. Therefore, the “wherein the disk covers an entirety of the second side of the stator and inner radius approximates an outer radius of a rotor shaft” must be shown or the feature(s) canceled from the claim(s). No new matter should be entered. Corrected drawing sheets in compliance with 37 CFR 1.121(d) are required in reply to the Office action to avoid abandonment of the application. Any amended replacement drawing sheet should include all of the figures appearing on the immediate prior version of the sheet, even if only one figure is being amended. The figure or figure number of an amended drawing should not be labeled as “amended.” If a drawing figure is to be canceled, the appropriate figure must be removed from the replacement sheet, and where necessary, the remaining figures must be renumbered and appropriate changes made to the brief description of the several views of the drawings for consistency. Additional replacement sheets may be necessary to show the renumbering of the remaining figures. Each drawing sheet submitted after the filing date of an application must be labeled in the top margin as either “Replacement Sheet” or “New Sheet” pursuant to 37 CFR 1.121(d). If the changes are not accepted by the examiner, the applicant will be notified and informed of any required corrective action in the next Office action. The objection to the drawings will not be held in abeyance. The new FIG. 2 is new matter, as it includes details not disclosed in the original drawings or specification. Conclusion 07-40 AIA Applicant's amendment necessitated the new ground(s) of rejection presented in this Office action. Accordingly, THIS ACTION IS MADE FINAL . See MPEP § 706.07(a). Applicant is reminded of the extension of time policy as set forth in 37 CFR 1.136(a). A shortened statutory period for reply to this final action is set to expire THREE MONTHS from the mailing date of this action. In the event a first reply is filed within TWO MONTHS of the mailing date of this final action and the advisory action is not mailed until after the end of the THREE-MONTH shortened statutory period, then the shortened statutory period will expire on the date the advisory action is mailed, and any nonprovisional extension fee (37 CFR 1.17(a)) pursuant to 37 CFR 1.136(a) will be calculated from the mailing date of the advisory action. In no event, however, will the statutory period for reply expire later than SIX MONTHS from the mailing date of this final action. Any inquiry concerning this communication or earlier communications from the examiner should be directed to MINKI CHANG whose telephone number is (571)270-0521. The examiner can normally be reached 9:00 AM - 5:00 PM. Examiner interviews are available via telephone, in-person, and video conferencing using a USPTO supplied web-based collaboration tool. To schedule an interview, applicant is encouraged to use the USPTO Automated Interview Request (AIR) at http://www.uspto.gov/interviewpractice. If attempts to reach the examiner by telephone are unsuccessful, the examiner’s supervisor, Seye Iwarere can be reached at (571) 270-5112. The fax phone number for the organization where this application or proceeding is assigned is 571-273-8300. Information regarding the status of published or unpublished applications may be obtained from Patent Center. Unpublished application information in Patent Center is available to registered users. To file and manage patent submissions in Patent Center, visit: https://patentcenter.uspto.gov. Visit https://www.uspto.gov/patents/apply/patent-center for more information about Patent Center and https://www.uspto.gov/patents/docx for information about filing in DOCX format. For additional questions, contact the Electronic Business Center (EBC) at 866-217-9197 (toll-free). If you would like assistance from a USPTO Customer Service Representative, call 800-786-9199 (IN USA OR CANADA) or 571-272-1000. /MINKI CHANG/Examiner, Art Unit 2834 /OLUSEYE IWARERE/Supervisory Patent Examiner, Art Unit 2834 Application/Control Number: 17/601,117 Page 2 Art Unit: 2834 Application/Control Number: 17/601,117 Page 3 Art Unit: 2834 Application/Control Number: 17/601,117 Page 4 Art Unit: 2834 Application/Control Number: 17/601,117 Page 5 Art Unit: 2834 Application/Control Number: 17/601,117 Page 6 Art Unit: 2834
Prosecution Insights