DETAILED ACTION
Notice of Pre-AIA or AIA Status
The present application, filed on or after March 16, 2013, is being examined under the first inventor to file provisions of the AIA .
Summary of the Claims
The present application (18/668,365) was filed on May 20, 2024 and claims priority to TW 113110208 filed on March 19, 2024. Claims 1-6 are pending. Claim 1 is the only independent claim.
References and Documents Cited in this Action
Hwang (US 10,418,780 B1)
Summary of Rejections and Objections in this Action
Examiner objects to claim 1 for minor informalities.
Claims 1-6 are rejected under 35 U.S.C. 112(b) as being indefinite.
Claim Objections
Claim 1 is objected to because of the following informalities:
The word “Whereby” in the last clause of the claim should be in lowercase.
Appropriate correction is required.
Claim Rejections - 35 USC § 112
The following is a quotation of 35 U.S.C. 112(b):
(b) CONCLUSION.—The specification shall conclude with one or more claims particularly pointing out and distinctly claiming the subject matter which the inventor or a joint inventor regards as the invention.
The following is a quotation of 35 U.S.C. 112 (pre-AIA ), second paragraph:
The specification shall conclude with one or more claims particularly pointing out and distinctly claiming the subject matter which the applicant regards as his invention.
Claims 1-6 are rejected under 35 U.S.C. 112(b) or 35 U.S.C. 112 (pre-AIA ), second paragraph, as being indefinite for failing to particularly point out and distinctly claim the subject matter which the inventor or a joint inventor (or for applications subject to pre-AIA 35 U.S.C. 112, the applicant), regards as the invention.
Claim 1 is indefinite for multiple reasons as discussed below.
First, claim 1 recites “a second pin” connected to negative power supply in lines 3-4 and “a ground pin” in line 16. It is unclear if the second pin is the ground pin (the specification consistently describes the second pin as being a ground terminal or ground pin; e.g., in Figure 5).
Second, claim 1 recites “the positive and negative power supplies” in lines 4-5, “the light emitting surface” in line 7, “the resistance value” in lines 30, and “the PWM control” in line 33. There is insufficient antecedent basis for these limitations.
Third, claim 1 recites “the laser diode current” in line 19, “the laser output power” in lines 27-28, and “the laser rate” in line 28. Claim 1 also recites “the optical power value of the laser diode,” the optical power change” and “the power value written by the automatic power write circuit” in lines 34-37. There is insufficient antecedent basis for these limitations. The claim appears to recite various terms referring to the same thing, namely, the power of the laser diode, and does not clearly distinguish between a value corresponding to the power that is output by the laser diode and detected by the photodiode, and a value corresponding to an input to the laser diode to determine what the laser diode power will be.
Fourth, claim 1 recites “an error amplifier parallel connected to the photodiode, responsible for the circuit and determining the laser diode current” in lines 18-19. The claim is indefinite because it is unclear which “circuit” to which this limitation refers (the claim recites several “circuit” elements) and it is also unclear how the error amplifier is “responsible” for a circuit.
Fifth, claim 1 recites “the photodiode…notifies the optical power change in the form of circuit feedback” in lines 34-35. The claim is indefinite because it is unclear what element is “notified” by the photodiode and to which circuit the photodiode feeds back to (the claim recites several “circuit” elements).
Sixth, claim 1 recites “the photodiode…immediately makes current compensation, so that the optical power can be stably maintained at the power value written by the automatic power write circuit (APW IC)” in lines 36-38. The claim is indefinite because the photodiode does not directly “make current compensation” but rather, the photodiode’s connections to other elements may enable those elements to perform current compensation. However, such connections are not recited.
Claims 2-6 depend on claim 1 and are indefinite for the same reasons as the parent claim.
Allowable Subject Matter
Claims 1-6 may be allowable if rewritten or amended to overcome the rejection(s) under 35 U.S.C. 112(b) or 35 U.S.C. 112 (pre-AIA ), 2nd paragraph, set forth in this Office action.
Hwang teaches, among other things, a dot projector with automatic power control (Figure 7; column 6, lines 1-26) including a first pin P1, a ground pin G, and a third pin P3; a photodiode 321; a laser diode 34; a logic circuit LE coupled to the first pin and the third pin; an error amplifier EA parallel connected to the photodiode; a protection circuit U connected to the error amplifier as a reference voltage; a transistor T separately connected to the error amplifier, a laser diode output pin P5 and the ground pin G in series connection; a current monitoring circuit CM parallel connected to the transistor T and coupled to the ground pin G; and an adjustment circuit VR, connected between the photodiode and the ground pin, the adjustment circuit changes the resistance value of a resistor.
The prior art does not specifically disclose or fairly suggest a dot projector with automatic power write including the combination of all of the elements, steps, and limitations recited in claims 1-6 (including all of the limitations of any respective parent claims and as well as the claims may be understood with respect to 35 U.S.C. 112(b) as discussed above), particularly including:
a PWM controller, connected to the third pin and coupled between the error amplifier and the transistor for writing functions to set the laser output power and PWM to adjust the laser rate; and an adjustment circuit, connected between the photodiode and the ground pin, the adjustment circuit changes the resistance value of a resistor according to a trim code (TRC), which uses a decoder to output to select different resistance values for writing, and the pin to which it is written is the same as the third pin of the PWM control, in combination with all of the elements and limitations.
Conclusion
Any inquiry concerning this communication or earlier communications from the examiner should be directed to Christina Leung at telephone number (571) 272-3023. If attempts to reach the examiner are unsuccessful, the examiner’s supervisor, Patricia Engle can be reached at (571) 272-6660.
Examiner interviews are available via telephone, in-person, and video conferencing using a USPTO supplied web-based collaboration tool. To schedule an interview, Applicant is encouraged to use the USPTO Automated Interview Request (AIR) at https://www.uspto.gov/patents/laws/interview-practice.
Information regarding the status of published or unpublished applications may be obtained from Patent Center. Unpublished application information in Patent Center is available to registered users. To file and manage patent submissions in Patent Center, visit: https://patentcenter.uspto.gov. Visit https://www.uspto.gov/patents/apply/patent-center for more information about Patent Center and https://www.uspto.gov/patents/docx for information about filing in DOCX format. For additional questions, contact the Electronic Business Center (EBC) at 866-217-9197 (toll-free). If you would like assistance from a USPTO Customer Service Representative, call 800-786-9199 (IN USA OR CANADA) or 571-272-1000.
/CHRISTINA Y. LEUNG/ Primary Examiner, Art Unit 3991