DETAILED ACTION
The present application and its arguments have been reviewed and currently claim 12 is rejected, claims 1-3, 5-11, and 13-16 are allowed, and claim 4 is cancelled.
Notice of Pre-AIA or AIA Status
The present application, filed on or after March 16, 2013, is being examined under the first inventor to file provisions of the AIA .
Response to Arguments
Applicant’s arguments, see page 35, filed 5/14/2026, with respect to 1-3 have been fully considered and are persuasive because Applicant has amended claim 1 with the provision and cancellation of claim 4. Therefore, the 103 rejection of claims of 1-3 has been withdrawn.
Drawings
The drawings were received on 5/14/2026. These drawings are accepted, however, the top width measurement 27 of the retaining ring 4 appears to be improperly measured as outlined below.
The drawings are objected to because:
In figure 4, near 27, the top measurement is measured from the left side of the retaining ring to the right side of the sidewall of the groove near 28 instead of an end of the retaining ring as outlined below in annotated figure 4 (ex., it appears the width of the retaining ring would have been started and ended at edges of the retaining ring compared to measuring the width of the retaining ring from an end of the retaining ring to a sidewall of the groove).
Corrected drawing sheets in compliance with 37 CFR 1.121(d) are required in reply to the Office action to avoid abandonment of the application. Any amended replacement drawing sheet should include all of the figures appearing on the immediate prior version of the sheet, even if only one figure is being amended. The figure or figure number of an amended drawing should not be labeled as “amended.” If a drawing figure is to be canceled, the appropriate figure must be removed from the replacement sheet, and where necessary, the remaining figures must be renumbered and appropriate changes made to the brief description of the several views of the drawings for consistency. Additional replacement sheets may be necessary to show the renumbering of the remaining figures. Each drawing sheet submitted after the filing date of an application must be labeled in the top margin as either “Replacement Sheet” or “New Sheet” pursuant to 37 CFR 1.121(d). If the changes are not accepted by the examiner, the applicant will be notified and informed of any required corrective action in the next Office action. The objection to the drawings will not be held in abeyance.
PNG
media_image1.png
730
710
media_image1.png
Greyscale
Claim Rejections - 35 USC § 112
The following is a quotation of 35 U.S.C. 112(d):
(d) REFERENCE IN DEPENDENT FORMS.—Subject to subsection (e), a claim in dependent form shall contain a reference to a claim previously set forth and then specify a further limitation of the subject matter claimed. A claim in dependent form shall be construed to incorporate by reference all the limitations of the claim to which it refers.
The following is a quotation of pre-AIA 35 U.S.C. 112, fourth paragraph:
Subject to the following paragraph [i.e., the fifth paragraph of pre-AIA 35 U.S.C. 112], a claim in dependent form shall contain a reference to a claim previously set forth and then specify a further limitation of the subject matter claimed. A claim in dependent form shall be construed to incorporate by reference all the limitations of the claim to which it refers.
Claim 12 is rejected under 35 U.S.C. 112(d) or pre-AIA 35 U.S.C. 112, 4th paragraph, as being of improper dependent form for failing to further limit the subject matter of the claim upon which it depends, or for failing to include all the limitations of the claim upon which it depends.
In this case, claim 12 is in improper dependent form for failing to further limit the subject matter of the claim upon which it depends because claim 9 already comprises all of the limitations of claim 12 (ex., claim 9 imports all of the limitations of claim 1; ex., claims 13 and 14 also depend from claim 12).
Applicant may cancel the claim(s), amend the claim(s) to place the claim(s) in proper dependent form, rewrite the claim(s) in independent form, or present a sufficient showing that the dependent claim(s) complies with the statutory requirements.
Allowable Subject Matter
Claims 1-3, 5-11, and 13-16 are allowed.
Conclusion
THIS ACTION IS MADE FINAL. Applicant is reminded of the extension of time policy as set forth in 37 CFR 1.136(a).
A shortened statutory period for reply to this final action is set to expire THREE MONTHS from the mailing date of this action. In the event a first reply is filed within TWO MONTHS of the mailing date of this final action and the advisory action is not mailed until after the end of the THREE-MONTH shortened statutory period, then the shortened statutory period will expire on the date the advisory action is mailed, and any nonprovisional extension fee (37 CFR 1.17(a)) pursuant to 37 CFR 1.136(a) will be calculated from the mailing date of the advisory action. In no event, however, will the statutory period for reply expire later than SIX MONTHS from the mailing date of this final action.
Any inquiry concerning this communication or earlier communications from the examiner should be directed to ALEXANDER TYLER RUFRANO whose telephone number is (571)272-6223. The examiner can normally be reached Mon - Fri 8:30AM to 4:30PM.
Examiner interviews are available via telephone, in-person, and video conferencing using a USPTO supplied web-based collaboration tool. To schedule an interview, applicant is encouraged to use the USPTO Automated Interview Request (AIR) at http://www.uspto.gov/interviewpractice.
If attempts to reach the examiner by telephone are unsuccessful, the examiner’s supervisor, Matthew Troutman can be reached at (571) 270-3654. The fax phone number for the organization where this application or proceeding is assigned is 571-273-8300.
Information regarding the status of published or unpublished applications may be obtained from Patent Center. Unpublished application information in Patent Center is available to registered users. To file and manage patent submissions in Patent Center, visit: https://patentcenter.uspto.gov. Visit https://www.uspto.gov/patents/apply/patent-center for more information about Patent Center and https://www.uspto.gov/patents/docx for information about filing in DOCX format. For additional questions, contact the Electronic Business Center (EBC) at 866-217-9197 (toll-free). If you would like assistance from a USPTO Customer Service Representative, call 800-786-9199 (IN USA OR CANADA) or 571-272-1000.
/A.T.R./Examiner, Art Unit 3679
/Matthew Troutman/Supervisory Patent Examiner, Art Unit 3679
Prosecution Insights