Notice of Pre-AIA or AIA Status
The present application, filed on or after March 16, 2013, is being examined under the first inventor to file provisions of the AIA .
DETAILED ACTION
Restriction Election
Applicant's election of Group I on 01/06/2026 is hereby acknowledged. Groups II-IV are withdrawn from further consideration by the examiner, 37 CFR § 1.142(b), as being for a nonelected design.
Objections to the Drawings
The line quality is objected to. The lines appear fuzzy and pixelated. This will be problematic when the printed patent is further reduced in size to two-thirds in reproduction. Correction is required to show crisp, clean, clear lines. The background should also be completely white. All drawings must be made by a process which will give them satisfactory reproduction characteristics. Every line, number, and letter must be durable, clean, black, sufficiently dense and dark, and uniformly thick and well-defined. See 37 CFR 1.84(l). See annotated drawings below as an example; however, the problems exist throughout all of the figures.
PNG
media_image1.png
638
938
media_image1.png
Greyscale
The surface shading (and thus the features they depict) is difficult to see here because the line quality is poor. See annotated drawing below:
PNG
media_image2.png
465
502
media_image2.png
Greyscale
FIG. 1 shows an additional line on the corner of the display stand that is not present on the same corner in any other drawing. Consistency is needed. See annotated drawing below:
PNG
media_image3.png
228
454
media_image3.png
Greyscale
FIG. 1 is objected to because the recessed areas on the exterior have additional lines across them that make them look closed; however, in other views, they are open. See annotated drawing below:
PNG
media_image4.png
448
660
media_image4.png
Greyscale
Non-Final Rejection under 35 USC § 112(a) and (b)
The claim is rejected under 35 USC § 112(a) and (b) as the claimed invention is not described in such full, clear, concise and exact terms as to enable any person skilled in the art to make and use the same, and fails to particularly point out and distinctly claim the subject matter which the inventor or joint inventor regards as the invention. The claim is indefinite and non-enabling for the following reason:
Due to a lack of surface shading, it is not clear whether the long parallel features are surface indicia on a flat plane or if they are recesses or depressions. If they are recesses, it is not clear how deep into the display stand they go. Are there variations between them or are they consistent?
By comparison, the circular features at the corners of each square have surface shading in FIG. 1 which indicates they are not surface indicia but actually recesses. The same circular features, however, in FIG. 2 don’t have surface shading. It could be inferred that the long parallel features are surface indicia as they are never depicted with surface shading? If they are meant to be recesses, the area within the border of the long parallel features may need to be disclaimed to enable them. See annotated drawing below:
PNG
media_image5.png
576
390
media_image5.png
Greyscale
Due to the features on the top surface of the display stand not being depicted clearly, the claimed design is in fact subject to multiple interpretations, and one of ordinary skill in the art would not be able to reproduce the design without the use of conjecture. This renders the claim indefinite and non-enabled.
To overcome this rejection, it is suggested that applicant submit new drawings of the claimed design that show the design clearly and consistently. If certain non-enabled portions of the design cannot be fully enabled without the introduction of new matter, applicant may remove from the claim the areas or portions of the design that are considered indefinite and non-enabling by converting them to broken lines, and amending the specification to indicate those portions form no part of the claimed design.
Replacement Drawings
Any amended replacement drawing sheet should include all of the figures appearing on the immediate prior version of the sheet, even if only one figure is being amended. The figure or figure number of an amended drawing should not be labeled as “amended.”
Each drawing sheet submitted after the filing date of an application must be labeled in the top margin as either “Replacement Sheet” or “New Sheet” pursuant to 37 CFR § 1.121(d). If the changes are not accepted by the examiner, the applicant will be notified and informed of any required corrective action in the next Office action. When preparing new or replacement drawings, be careful to avoid introducing new matter. New matter is prohibited by 35 USC § 132 and 37 CFR § 1.121(f).
Conclusion
Accordingly, the claim stands rejected under 35 USC § 112(a) and (b) as set forth above. The prior art made of record and not relied upon is considered pertinent to applicant's disclosure.
CONTACT INFORMATION
Any inquiry concerning this communication or earlier communications from the examiner should be directed to ALEXANDRIA DUBUS whose telephone number is (703)756-1979. The examiner can normally be reached M-F | 12:00 PM - 9:00 PM ET.
Examiner interviews are available via telephone, in-person, and video conferencing using a USPTO supplied web-based collaboration tool. To schedule an interview, applicant is encouraged to use the USPTO Automated Interview Request (AIR) at http://www.uspto.gov/interviewpractice.
If attempts to reach the examiner by telephone are unsuccessful, the examiner’s supervisor, Ian Simmons can be reached at (571) 272-2658. The fax phone number for the organization where this application or proceeding is assigned is 571-273-8300.
Information regarding the status of published or unpublished applications may be obtained from Patent Center. Unpublished application information in Patent Center is available to registered users. To file and manage patent submissions in Patent Center, visit: https://patentcenter.uspto.gov. Visit https://www.uspto.gov/patents/apply/patent-center for more information about Patent Center and https://www.uspto.gov/patents/docx for information about filing in DOCX format. For additional questions, contact the Electronic Business Center (EBC) at 866-217-9197 (toll-free). If you would like assistance from a USPTO Customer Service Representative, call 800-786-9199 (IN USA OR CANADA) or 571-272-1000.
/A.D./Examiner, Art Unit 2913 /BRETT MILLER/Examiner, Art Unit 2934